Перегляд за автором "Sheng, L.Y."

Результати 1-7 з 7

Assessment of the Microstructure and Mechanical Properties of a Laser-Joined Carbon Fiber-Reinforced Thermosetting Plastic and Stainless Steel

Sheng, L.Y.; Jiao, J.K.; Lai, C. (Проблемы прочности, 2018)

The thermosetting plastic and stainless steel were joined with a fiber laser. The influence of processing parameters on the joint was studied. The laser scanning on stainless steel is shown to result in the formation of ...
Effect of the Surface Texture on Laser Joining of a Carbon Fiber-Reinforced Thermosetting Plastic and Stainless Steel

Sheng, L.Y.; Lai, C.; Xu, Z.; Jiao, J. (Проблемы прочности, 2019)

A carbon fiber-reinforced thermosetting plastic and stainless steel were joined by the fiber laser. The surface texture effect on the joint was investigated. The abrasive paper scratching is shown to form single directional ...
Hot Extrusion Effect on the Microstructure and Mechanical Properties of a Mg–Y–Nd–Zr Alloy

Sheng, L.Y.; Du, B.N.; Wang, B.J.; Xu, D.K.; Lai, C.; Gao, Y.; Xi, T.F. (Проблемы прочности, 2018)

A Mg–Y–Nd–Zr alloy was prepared by casting and hot extrusion. The microstructure and mechanical properties of OM, SEM, XRD, TEM, and tensile tests were investigated with casting and hot extruded alloys. The results ...
Influence of Tantalum Addition on Microstructure and Mechanical Properties of the NiAl-Based Eutectic Alloy

Sheng, L.Y.; Du, B.N.; Lai, C.; Guo, J.T.; Xia, T.F. (Проблемы прочности, 2017)

NiAl-28Cr-6Mo or NiAl-Cr(Mo) eutectic alloys with different degree of tantalum (Ta) addition have been fabricated and investigated. The microstructural characterization shows that minor Ta addition results in the formation ...
Microstructure and Wear Properties of the Quasi-Rapidly Solidified NiAl/ Cr(Mo,Dy) Hypoeutectic Alloy

Sheng, L.Y. (Проблемы прочности, 2016)

The NiAl/Cr(Mo,Dy) hypoeutectic alloy was prepared by quasi-rapid solidification to investigate its microstructure and wear behavior. The results revealed that the quasi-rapid solidification refined the eutectic cell and ...
Optimization of the Microstructure and Mechanical Properties of a Laves Phase-Strengthened Hypoeutectic NiAl/Cr(Mo,W) Alloy by Suction Casting

Sheng, L.Y.; Du, B.; Zan, S.P.; Lai, C.; Jiao, J.K.; Gao, Y.B.; Xi, T.F. (Проблемы прочности, 2018)

A niobium (Nb)-doped NiAl/Cr(Mo,W) hypoeutectic alloy was prepared by conventional and suction casting methods. Its microstructure and compression properties were studied to evaluate the effect of a manufacturing process. ...
Shear Strength Optimization of Laser-Joined Polyphenylene Sulfide-Based CFRTP and Stainless Steel

Sheng, L.Y.; Wang, F.Y.; Wang, Q.; Jiao, J.K. (Проблемы прочности, 2018)

A thermosetting plastic and stainless steel were joined by the fiber laser with and without polyphenylene sulfide (PPS) additive. Its microstructure, interface morphology, and shear strength were investigated.

Результати 1-7 з 7

Пошук

Розширений пошук

Перегляд

Вся бібліотека

Перегляд за автором "Sheng, L.Y."

Репозиторій DSpace/Manakin

Перегляд за автором "Sheng, L.Y."

Пошук

Перегляд

Вся бібліотека

Мій обліковий запис